A swing gate opens like a big door and carries its whole weight on a few hinges. Over the years that weight pulls the gate down, hinges wear and the operator arm starts to fight the gate instead of guiding it. The result is a gate that drags, will not latch, bangs in the wind or makes the opener give up halfway.
Braxdyne offers swing gate repair in Sacramento and nearby cities in Placer, El Dorado, Yolo, Sutter and San Joaquin counties. We work on single and double swing driveway gates at homes, including hinges, operator arms and brackets, latches and gate stops. We see common residential operators such as LiftMaster, Mighty Mule, US Automatic, Viking and Ghost Controls.
Every visit starts with a $0 service call and a free estimate, and we agree on the price before any work begins. Our work carries a 90-day labor warranty, and parts we install carry a 1-year parts warranty. We are open 7am to 9pm every day and take emergency calls until midnight.
Braxdyne is not yet licensed by the CSLB (our license is in process), so we only take minor repairs under $1,000 total for parts and labor that need no permit, and we refer bigger jobs to a licensed partner.
Signs you need swing gate repair
- The gate sags, and the far end sits lower than the hinge end.
- The gate drags or scrapes on the driveway as it swings.
- The two leaves of a double gate no longer meet in the middle.
- The latch will not catch, or you have to lift the gate to close it.
- The operator arm clunks or jerks, or a bracket is bent or loose.
- The gate was pushed around by strong wind and has not worked right since.
What we do on a visit
- Look at the whole gate. We check the posts, hinges, frame, latch, stops and how the operator arm is mounted.
- Test the gate by hand. With the operator released the way the manufacturer intends, we swing the gate through its full travel to feel for binding and drag.
- Check hinges and arms. We look for worn pins, loose bolts and shifted hinges, and check the arm, its pins and its bracket angles. A bracket that moved even a little can make the arm push the wrong way.
- Check latch and stops. We confirm the gate stops in the right place and the latch lines up.
- Agree on a price. You get our recommendation and the price before any work starts.
- Repair, adjust and test. We fix or replace worn parts, reset limits if needed, cycle the gate several times and confirm the safety devices still stop or reverse it.
Common swing gate problems we fix
Sagging and dragging. Sometimes the fix is adjustable hinges, new hinge hardware or tightening loose bolts. Sometimes the ground has shifted, the post leans or the frame has bent. We fix the hardware side and tell you honestly when the post or frame is the real issue.
Worn hinges. Hinge pins and bushings wear with every swing, letting the gate drop and wobble and making the operator work harder. We replace worn hinges with parts sized for your gate where the existing mounting allows.
Operator arms and brackets. Loose bolts, bent brackets, worn pins and a wrong mounting angle cause clunking, jerky motion and early wear. We tighten, realign or replace these parts when the job fits our limits.
Latches and gate stops. When stops or latches shift, the gate overshoots, bangs or will not stay shut. We realign or replace them.
Wind damage. A solid swing gate catches wind like a sail. A strong gust can bend an arm, strip gears or rip a bracket loose. We repair what fits our limits and tell you what needs more work.
Resetting a post in new concrete, welding a bent frame or building a new gate is fabrication work. If your gate needs it, we will tell you up front and refer you to a licensed partner.
What you can safely check yourself
Keep children, pets and cars clear of the gate while you look.
- Power. If the gate does nothing, check for a tripped breaker or popped GFCI outlet and reset it once.
- Remote batteries. If only the remote fails, try a fresh battery.
- The swing path. Look for rocks, mulch, bins or overgrown plants where the gate sweeps.
- Photo eyes. Wipe the lenses with a soft cloth and make sure nothing blocks the beam.
- Manual release. Only use it if your operator manual says how, and follow it exactly.
Do not lift, pry or re-hang a heavy gate leaf yourself. Never climb on, swing on or ride the gate, and never stand between a moving leaf and a post or wall.
When to call a technician
- A hinge is cracked or pulling out of the post, or the leaf hangs crooked.
- The gate drags hard enough to leave marks or stall the opener.
- The operator arm is bent, disconnected or clunking loudly.
- The gate will not latch, or it was hit by a car or damaged in a storm.
More gate help
Swing gate trouble and opener trouble often go together. See gate opener repair, sliding gate repair and gate keypad, remote and safety sensor repair, or visit our main electric gate repair page. For more simple checks, read Electric gate opener not working?
FAQ
Can a sagging swing gate be fixed, or does it need replacing?
Many sagging gates can be fixed with new or adjusted hinges and hardware. If the post leans or the frame is bent, the job may need concrete or welding work, and we refer that to a licensed partner.
Why does my double gate not meet in the middle anymore?
Usually one leaf has sagged, a hinge has worn, or an arm or limit setting has shifted. We check each leaf and line them back up.
The wind slammed my gate. What should I do?
Look from a safe distance for a bent arm, a loose bracket or a crooked leaf. Do not run the gate if anything looks bent or loose. Text us a photo and we will tell you the next step.
Swing gate sagging or dragging? Call Braxdyne at (916) 848-5050 or text a photo of your gate, hinges and operator arm. We are open 7am to 9pm every day, with emergency calls until midnight, a $0 service call and a price agreed before any work.



